







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Kitchen Remodeling: The Fremont Owner’s Guide
Unilock kitchen remodeling in Fremont runs $14,000 – $45,000 installed, and the number lands closer to the middle when the layout stays put and the cabinets, counters, and backsplash are straight swaps rather than a full teardown. Most Fremont owners don’t call us because they want a new kitchen – they call because something in a Unilock-built or Unilock-finished kitchen failed and they can’t find the exact part or the right installer. It usually starts small: a drawer that grinds, a door that hangs a half-inch low, a cabinet box that has pulled away from the wall over a 1960s slab. Then it gets worse, and the question becomes whether to source the component or rebuild the run. We handle both.

Key Takeaways
- Installed Unilock-compatible kitchen work in Fremont: $14,000 – $45,000.
- Cabinet installation alone: $4,000 – $13,000. Countertops: $2,000 – $6,500.
- We’re an independent Fremont contractor, not affiliated with Unilock.
- We don’t stockparts and no crew member carries parts on a truck. We verify your model, source the correct fit, and install it.
Which Unilock Models This Applies To

Unilock hardware and cabinetry lines change specification by series and by production year, and the same nominal part – a soft-close hinge, a drawer glide, a cabinet leg – differs by a few millimeters between series. A glide that fits a 2014 run often won’t seat in a 2019 box even though the fronts look identical. So before we quote anything, we identify the exact series from the label inside the cabinet door or drawer box, measure the hinge cup bore (usually 35mm, sometimes 26mm on older or compact lines), and confirm the drawer glide length and mounting pattern. That label is the single thing that makes or breaks the match – photograph it before you call.
On OEM versus aftermarket for Unilock specifically: OEM hardware guarantees the fit and the finish match, and it’s the right call when a single failed component is under warranty or when the cabinet is in a visible spot. A quality aftermarket equivalent – a reputable soft-close hinge or glide of the same bore and length – is often sturdier than the original and cheaper, and for a run of five or more you’ll feel the difference in price. We’ll lay out both in writing so you can choose. If your kitchen also uses KraftMaid, Cambria, or Silestone components, we source those to spec too.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Kitchen Remodeling Is Failing
- Doors that won’t stay closed or swing past their stop. The soft-close hinge has lost its dampening, or the adjusting screw has stripped. Once the damping fails the door slams, and slamming wears the cup bore until the hinge won’t hold.
- Drawers that grind or jump the track. A worn glide roller or a bent track. In Fremont’s dry summer air, wood drawer boxes shrink slightly, and a glide that was snug in spring starts to rattle by August.
- Cabinet boxes separating from the wall or from each other. Failed fasteners or a shifted leg, common in older Fremont homes where the wall itself has settled. This one gets dangerous fast if the run is loaded with dishes.
- Countertop seams opening or caulk lines cracking. Movement in the cabinet base telegraphs up. A seam that opens isn’t a caulk problem – it’s a sign the base underneath has shifted.
- Water staining at the sink base or along the backsplash. A failed seal or a slow leak behind the counter. Left alone, it rots the cabinet bottom and the substrate under the tile.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what the work runs in Fremont, parts and labor together, quoted as a written line item before anything starts:
| Scope | Installed Range |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What moves the number: whether the layout changes (plumbing and electrical relocation is the big one), the cabinet series and finish, countertop material, and how much of the existing run can be saved. A single failed hinge or glide is a small repair; a run that has separated from the wall is a reinstall with new fasteners and possibly a new base. Every scope, every allowance, and every price change arrives as a written change order before work happens – an allowance that isn’t on paper is a surprise waiting for a date. Every eligible job gets permits pulled and inspections signed, and the finished work is backed by our written 90-Day Done Right Promise.
DIY or Call Us?
You can safely check a few things yourself: photograph the series label inside the door, measure the hinge bore and glide length, and tighten the adjusting screws on a soft-close hinge to see if the door realigns. That’s diagnostic, not repair.
Where DIY goes wrong is when the cabinet run has separated from the wall or the base has shifted under a stone counter. A loaded upper cabinet pulling off drywall can come down on a person, and a stone counter that shifts can crack or drop. Those aren’t a screwdriver job – they need proper fastening into studs and a check of what the wall is actually holding. When a part is genuinely dangerous to swap or the failure is structural, stop and let a trained crew member handle it. Call us at (833) 620-6162 and we’ll tell you straight whether it’s a repair or a rebuild.
FAQs

Quality soft-close hinges and drawer glides typically give 10 to 15 years of daily use before dampening or glide action degrades, and Fremont’s dry summers and mild winters are gentler on hardware than a humid climate – the bigger wear factor here is heat cycling near the range and sun exposure through south-facing windows. Cabinet boxes and frames themselves last far longer than the moving parts bolted to them.
Often yes. A soft-close hinge that’s lost dampening can sometimes be re-adjusted rather than swapped, and a single glide can be replaced without touching the rest of the run. We’ll check whether the failure is the part or the mounting before recommending a full replacement – no reason to sell you a new cabinet when a $30 hinge does the job. Call (833) 620-6162 for a free second opinion on any written estimate.
A single hinge or glide is usually a same-visit fix once the correct part is sourced and on site. A cabinet run reinstall or countertop reset runs longer, often a couple of days depending on scope and whether permits are involved. We’ll give you the timeline in writing before we start.
We identify the exact Unilock series from the cabinet label and measurements, then source the correct OEM component or a verified aftermarket equivalent of the same bore, length, and mounting pattern – we don’t guess from a photo. That sourcing step is what makes the fit right the first time. Call (833) 620-6162 to start with the label photo.
Ready to stop living with a kitchen that fights back? Call Barrett & Sons Construction Fremont at (833) 620-6162 for a free estimate – a live person answers around the clock, we publish our license number so you can look it up before you sign anything, and every price change is in writing before a single nail moves. Proudly serving Fremont and the surrounding communities for over 29 years, with our Senior & Veteran 10% discount standing for those who’ve earned it.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












