







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Windows & Doors: The Fremont Owner’s Guide
We install Unilock-compatible windows and doors for Fremont homeowners, and most full window replacements here land between $4,500 and $15,000 depending on count, glass package, and frame material. Impact-rated units, which a growing number of Fremont owners choose near the Hayward fault corridor, run $8,000 to $25,000. We’re an independent service provider, not affiliated with Unilock, and we don’t stock parts or carry them on a truck – we measure your unit and source the correct replacement before we schedule the install.

Owners in Fremont usually discover a failing Unilock unit the same way. A window that used to slide now needs a shove. The latch on a patio door catches halfway. Or you find a thin line of water on the sill after a windy February rain, and it keeps coming back every storm. The part itself is often small – a sash balance, a roller assembly, a multipoint lock cartridge, a weatherstrip gasket – but the symptoms show up as drafts, sticking, fogging, or water where water shouldn’t be.
Which Unilock Models This Applies To

Unilock has built vinyl and aluminum window and door products across several series over the years, and the parts are not interchangeable between them. A sash balance that fits one series will not fit another, and the same goes for rollers, lock cartridges, and screen frames. Before we order anything, we identify your unit the way a parts counter should:
- The manufacturer label. Most Unilock units carry a sticker on the sash edge, the head jamb, or the door panel edge. It usually lists the series, the model number, and a date code. Photograph it before you do anything else.
- Glass markings. The etched code in the corner of the glass tells us the glazing package, which matters if you’re matching a unit that’s already been replaced on one side of the house.
- Rough opening measurements. Width, height, and depth of the frame, taken in three places each. Vinyl frames can shift a fraction over time, so we measure the actual opening, not the old unit’s nominal size.
On the OEM-versus-aftermarket question: for Unilock specifically, some older series have thin factory parts support, and a quality aftermarket balance or roller is often the better call – it’s built to the same dimensions, sometimes with a heavier spring or a sealed bearing that outlasts the original. Where the part is a lock cartridge or a proprietary hinge, we stick with OEM-equivalent so the door still secures and passes inspection. We tell you which way we’re going and why before we order.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Windows & Doors Is Failing
- The sash won’t stay up, or slams down. The spiral or block-and-tackle balance has lost tension or snapped. This is the single most common failure we see on Fremont vinyl sliders and single-hungs, and it’s a $60 to $180 part most of the time.
- The window is hard to open or feels gritty. Rollers and pivot shoes wear out, and Fremont’s dry summers followed by wet winters swell and shrink the frame slightly, which accelerates the wear. Cleaning and lubricating the track buys a few months; replacing the roller fixes it.
- Water on the sill after a storm. A failed weatherstrip gasket, a clogged weep hole, or a shifted sill pan. This one matters most in Fremont because our wind-driven rain comes sideways and finds every gap. Left alone, it rots the framing behind the drywall.
- Fogging between the panes. The sealed glass unit has lost its desiccant seal and moisture has gotten in. No part swap fixes this – the insulated glass unit has to be replaced, or the whole sash if the unit is older.
- The patio door lock won’t engage, or engages only with a lift and a shove. A worn multipoint lock cartridge, a dropped roller, or a sagging hinge. On a Fremont door facing the afternoon sun, heat cycling can warp the panel over a decade and throw the lock out of alignment.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s the honest range for Fremont, with the parts-and-labor split shown so you can see where the money goes:
| Job | Installed Range | What’s Included |
|---|---|---|
| Single window replacement (Unilock-compatible) | $450 – $1,200 per unit | Unit, glass, install, flashing, sealant |
| Full window replacement, typical home | $4,500 – $15,000 | All units, trim, permits, haul-away |
| Impact-rated window installation | $8,000 – $25,000 | Impact glass, reinforced frames, permit |
| Patio door replacement (single) | $1,200 – $3,500 | Door, hardware, threshold, flashing |
The range drivers are simple: how many units, whether you’re matching existing trim or replacing it, glass package (standard vs. low-E vs. impact), and whether the rough opening is square. Permits are pulled and inspections signed on every eligible job – the permit inspector works for you, not for us, which is exactly why we want him on site. Our crew members are background-checked and uniformed on every visit, and every job is backed by our written 90-Day Done Right Promise. Whatever brand you have elsewhere in the house – KraftMaid, Cambria, Silestone, Andersen, Marvin – we match the finish and the look so nothing reads as a patch.
DIY or Call Us?
Some of this you can safely check yourself. Open and close every window and door and note which stick. Look at the manufacturer label and photograph it. Clean the tracks and weep holes with a stiff brush and a shop vac – that alone fixes a surprising share of “hard to open” complaints. Check the weatherstrip for cracks or compression by running a finger along it. None of that is dangerous.
Where DIY goes wrong is the part swap itself. Sash balances are under real spring tension; on a block-and-tackle balance, releasing the wrong end can whip the cord and crack the glass, and on a spiral balance it can snap back at your hand. Glass units are heavy and awkward, and a dropped sash on a ladder is how people end up in the ER. Patio door rollers require lifting the panel out of the track, and a wrong-sized roller will bind and eventually bend the frame. If you’re not sure which part has failed, or the unit is more than a few years old, call us at (833) 620-6162 and we’ll look it over. Our crew members have up to 28 years of experience with windows and doors, and we’ll tell you straight whether a part swap, a sash replacement, or a full unit is the right call. Free second opinion on any written estimate, and no trip charge inside the county.
FAQs

Fifteen to twenty-five years is typical for the frame and hardware, with the sealed glass units often going first at around 12 to 18 years. In Fremont, the dry summers and wet winters work the frame more than a steady climate would, so seals and weatherstrip tend to wear faster than the glass on south- and west-facing units. Call (833) 620-6162 for a free estimate on what’s worth replacing now versus later.
Often yes – balances, rollers, weatherstrip, and lock cartridges are all replaceable on their own, and a repair runs a fraction of a full unit. Fogged glass units can sometimes get a new insulated glass unit dropped into the existing sash. The repair stops making sense when the frame itself is warped, rotted, or cracked, and that’s when we tell you to replace the unit. Call (833) 620-6162 and we’ll give you a written line-item quote both ways.
A single window is a half-day job for a typical Unilock-compatible unit, and a full-house replacement runs two to four days depending on count and trim. Patio doors are usually a single day. We schedule around your weather window and put the scope in writing before we start, so there’s no surprise on the schedule or the invoice. Call (833) 620-6162 to get on the schedule.
We identify the series from the manufacturer label and the glass markings, measure the rough opening, and order the correct part or unit from the supplier – we don’t guess and we don’t substitute a different series part. If the factory part is no longer supported, we source a quality aftermarket equivalent built to the same dimensions and tell you so in writing. No stock on a truck, no van full of mystery parts. Call (833) 620-6162 to start with a free estimate.
If your Unilock windows or doors have a part that’s failing, don’t sit on it through another wet season in Fremont. Call Barrett & Sons Construction Fremont at (833) 620-6162 for a free estimate – we’ll identify the unit, quote the repair and the replacement side by side, and put it all in writing before a single part comes out of the box. Every scope, every allowance, every price change in writing. 90-Day Done Right Promise on the work. A live person answers the phone, 24 hours a day. We also work on KraftMaid, Cambria, and Silestone products alongside your Unilock windows and doors, so if you’re already planning a kitchen or bath around this, we can line it all up in one written scope.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












