







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Kitchen Remodeling: The Fremont Owner’s Guide
In Fremont, we install KraftMaid and KraftMaid-compatible kitchen remodeling at a typical installed range of $14,000 to $45,000 for a full room, and $4,000 to $13,000 for cabinet installation alone. Fremont is Bay Area, and that matters for anything set into KraftMaid’s maple or plywood cabinet boxes or within its drawer-glide and soft-close hardware. The old wood moves with seasonal swings off the San Jose shoreline fog and the dry summer afternoons. Hardware, hinges, and connector tolerances open up. We’re an independent contractor; we don’t work for KraftMaid.

Most owners around Fremont don’t realize a cabinet interior has aged. They discover it when a cabinet door no longer closes flush, a drawer front catches the surrounding frame, or a hinge screws into softened wood that no longer holds. That’s the moment they search. This page is written for that moment.
Key takeaways
- Typical installed full-kitchen remodeling range in Fremont: $14,000 – $45,000.
- Cabinet installation only: $4,000 – $13,000.
- Countertop installation: $2,000 – $6,500.
- We can’t carry parts on a truck or stock them for you. We source what your KraftMaid model and series actually need, confirm the match, then install it.
- Every scope, every allowance, every price change arrives as a written change order before the work proceeds.
Which KraftMaid Models This Applies To

KraftMaid’s cabinet lines run through a few discernible families, and the right part depends on which family your kitchen sits in. The common groupings are their standard cabinet construction, their all-plywood box lines, and their full-access drawer/door offerings. The door overlay matters most: a full-overlay door takes a different hinge than a partial-overlay door, and if you fit the wrong one, the door won’t hang true or stay closed.
To identify what you have, look for the brand stamp and series label inside the cabinet door and on the interior side panel. If the label is gone, measure the door overlay (the amount the door extends past the opening), the cabinet depth, and the drawer glide clearance. A local hardware shop or a contractor can confirm the match from those measurements.
The OEM-versus-aftermarket decision matters for KraftMaid. The factory finish is a low-sheen lacquer or a catalyzed paint, and a hardware replacement from a generic aftermarket source usually fits mechanically but won’t match the finish tone. Matching the exact factory connectors, glide profile, and finish code is worth the effort on KraftMaid cabinetry; it’s the difference between a hinge that holds for years and one that pulls loose in a season. Our crew members have up to 28 years of experience, and matching box and hardware series is part of the job.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your KraftMaid Kitchen Remodeling Is Failing
- Doors sag or rub the frame. Often the hinge has worked loose because the hinge screws lost grip in the interior wood at the cabinet roll edge. In Fremont’s mix of dry summers and moist winters, the fiber of soft maple or particle core can open up around a screw and stop holding. A new screw in the same hole won’t grab.
- Drawers drag or stick halfway. The typical cause is a slider glide that’s worn or has a bent tab. KraftMaid’s full-access drawers run on a specific side-mount or undermount guide, and a mismatched guide produces a drawer that binds at one end. It goes unnoticed until a drawer stops closing cleanly.
- The soft-close damper quits. A soft-close hinge that stops cushioning and slams shut usually means the internal damper has failed, not the hinge itself. Replacing the whole hinge is often faster and more reliable than chasing just the damper when the model tolerance is unknown.
- Doors don’t sit flush across the face. That top gap that appeared over winter points to hinge screws that moved with the wood, or a cabinet box that has racked slightly. Racked boxes can be reset with shims; loose hinges need new screw placement. Both are fixable without new doors.
- Water staining or a soft base corner. A dishwasher leak or a slow condensation drip behind the sink can soften the base cabinet interior at the toe kick. That’s the one sign that isn’t a simple hardware swap, because once the base material is soft, attaching new screws won’t solve it. It’s a cabinet or cabinet-part replacement decision.
Replacement Cost & What’s Included

Here’s what the work actually runs in Fremont, with parts and labor separated in the quote so you can see where the money goes:
- Single hardware part plus install: typically $120 – $280 per piece depending on whether the hinge or glide is OEM-matched or aftermarket.
- Door or drawer front replacement: $180 – $400 per front, depending on door style and finish color.
- Cabinet installation, full room: $4,000 – $13,000.
- Countertop installation (Cambria, Silestone, or similar quartz): $2,000 – $6,500.
- Backsplash installation: $800 – $2,500.
- Full kitchen remodel (KraftMaid cabinetry, counters, install): $14,000 – $45,000.
What drives the range: cabinet count and finish tier, whether any box is racked or soft-cornered, countertop material (quartz runs higher than laminate), and whether a permit is required, which in Fremont depends on the scope. We pull the permit and get inspections signed on every eligible job. Hardware replacement, door-front swaps, and drawer-front swaps often don’t require one.
Every completed job is backed by the Barrett & Sons 90-Day Done Right Promise, written on the contract: if something isn’t right, Tom comes back and makes it right, one call. In Fremont, some of the popular quartz brands we install alongside KraftMaid are Cambria and Silestone, with Kohler fixtures if the scope includes them.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Tightening a loose screw, wiping down a hinge, or measuring your door overlay to identify a replacement part are safe jobs for an owner. So is looking up your KraftMaid series label. Swapping a soft-close hinge on an existing cabinet is entirely doable for most homeowners with the right part in hand. Where DIY goes wrong is when the base material has softened from water, or when the drawer guide profile is worn and a generic aftermarket part won’t sit in the original mounting holes. That’s the point where a $15 part turns into a wasted afternoon and a cabinet drawer that lines up worse than before.
What we can do is match the part to your KraftMaid model, source it, and install it right the first time. If we do the install, it carries the workmanship warranty and 90-Day Done Right Promise. Calling us costs nothing to get a written estimate.
FAQs

How long do KraftMaid hinges and drawer glides last in Fremont?
Most hinges and drawer glides hold up 10 to 20 years. In areas of Fremont close to the salt air and with seasonal humidity swings, the softer hardware components – especially the soft-close dampers – can start failing at the 8 to 12 year mark. Call (833) 620-6162 for a free estimate if yours are older and starting to act up.
Can a failing KraftMaid hinge be repaired instead of replaced?
Sometimes. If only the screw has pulled loose, a larger screw or a screw anchor in the same hole can buy a few more years. But if the hinge itself has lost tension, it needs replacing, because the internal spring can’t be re-tensioned. Call (833) 620-6162 for an exact quote on replacement parts and labor – estimates are free.
How long does a KraftMaid hinge or glide swap take?
A single hinge or glide swap takes 20 to 40 minutes in the field. Doing a whole kitchen is a half-day to a full day depending on how many hardware points are worn and whether any doors need adjustment. Call (833) 620-6162 to schedule and we’ll give you a window you can plan around.
How do you source the replacement part for my KraftMaid cabinets?
We ask for the series label from inside the cabinet door, or the door overlay and drawer-glide measurements if the label is missing, then match the part to the KraftMaid model. We don’t stock parts, but we’ll source and confirm the match before we come out. Call (833) 620-6162 to start the process – the estimate is free.
Do you carry insurance and pull permits for cabinet work in Fremont?
We’re licensed, insured, and bonded, and we pull the permit and get inspections signed on every eligible job in Fremont. Whether a permit is required for your scope depends on the city’s rules – we’ll tell you up front before any work starts. Call (833) 620-6162 for a free second opinion on any written estimate.
Get Your KraftMaid Parts and Remodeling Priced in Fremont
If your KraftMaid cabinets are acting up in Fremont, you don’t need to guess which part failed or whether it’s worth fixing. We offer a free second opinion on any written estimate, a no-hassle written quote before the work starts, and a permanent 10% senior and veteran discount. There’s a live person answering the phone 24/7, so call us at (833) 620-6162 for your free estimate.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












