







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Bathroom Remodeling: The Fremont Owner’s Guide
We complete KraftMaid bathroom remodeling projects in Fremont for a typical installed cost of $9,000 – $28,000, including tear-out, code-compliant rough-in, moisture-rated finishes, permits pulled and inspections signed. Cabinet, vanity and door parts get sourced to match your exact KraftMaid series rather than substituted with whatever a warehouse happens to stock. No job here happens same-day; a full bathroom is a multi-week build, and we quote it that way.

Owners usually discover a failed component slowly. A vanity door starts sagging and won’t stay on its hinges. A drawer glides rough after a wet winter. Paint lifts along the bottom rail of a cabinet near the shower. Sometimes it’s a soft spot in the toe kick or a hinge plate stripped out of particle board. Fremont’s dry summers and damp winters cycle bathroom humidity hard, and that’s where KraftMaid installations show their first wear. We’re Barrett & Sons Construction, an independent contractor, not affiliated with KraftMaid; we source compatible components and do the install work.
Key Takeaways
- A full KraftMaid bathroom remodel in Fremont runs $9,000 – $28,000 installed; small bathrooms run $5,000 – $12,000.
- Cabinet parts fail first at hinges, drawer glides and the bottom rail near wet zones.
- Match parts by the KraftMaid series label inside the cabinet box, not by eye.
- Permits and written change orders before work moves. Every time.
Which KraftMaid Models This Applies To

KraftMaid builds bathroom cabinetry in several door styles and finish programs, and parts don’t cross between them cleanly. A door from one series won’t fit a box cut for another, even at the same nominal width. That’s the compatibility gotcha most Fremont homeowners hit: they measure the opening and order a replacement, and the hinge bore spacing is wrong. KraftMaid uses different cup positions and overlay specs across product lines, so a 24-inch vanity cabinet from one program can reject a door built for another.
To identify yours, open the cabinet and find the label inside the door or on the back panel of the box. It lists series, finish and, in most cases, the part number. Photograph it before you do anything else. If the label’s gone, we measure the door height, width and thickness, then measure hinge cup diameter and bore distance from the edge; that set of numbers narrows the match. We don’t keep parts on a truck or in a warehouse, so nothing gets guessed at the curb.
OEM versus aftermarket is the real decision. For visible doors and drawer fronts, OEM keeps the finish and profile consistent across the room, and that matters when one door sits beside eleven others in an open Fremont bathroom. For hidden hardware (hinges, glides, shelf pins), a quality aftermarket equivalent from a known maker often performs as well or better for less money, and we’ll tell you when that’s the honest call. Our technicians have up to 28 years of experience matching cabinet components, Cambria and Silestone tops, and Kohler fixtures to existing KraftMaid layouts.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your KraftMaid Bathroom Remodeling Is Failing
Here’s what actually sends people looking for parts.
- Door sags or rubs the frame. The hinge screws have pulled out of the particle board, or the hinge itself has worn past its spring tension. Once the plate strips, tightening the screw won’t hold for long.
- Drawer glides catch or grind. Dust, hair and moisture collect in the glide track, and low-grade rollers flatten. In a bathroom that sees daily showers, this shows up years before it would in a hallway cabinet.
- Finish lifting at the bottom rail or around the sink. Water wicks into the edge and the paint or laminate lifts. This is the most common KraftMaid failure we see near a wet zone in Fremont bathrooms.
- Soft or swollen toe kick and side panel. Repeated small leaks under the sink or a shower splash that never quite dries soak into the panel base. Swelling doesn’t reverse.
- Warped door or gap at the top corner. Spring humidity swings in Fremont push a slightly under-sealed door out of flat, and the gap gives it away long before the door visibly bows.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed bathroom remodeling in Fremont runs $9,000 – $28,000 depending on size, layout changes and finish level. A small bathroom remodel lands at $5,000 – $12,000. If you’re replacing just the vanity, that’s $800 – $3,000 installed; a walk-in shower is $4,500 – $12,000; a tub-to-shower conversion is $3,500 – $10,000. Cabinet installation alone runs $4,000 – $13,000, and countertop work with Cambria or Silestone is $2,000 – $6,500.

What drives the range: whether the rough-in moves, whether permits trigger a layout change, tile selection and how much of the existing cabinetry gets reused versus replaced. Every allowance is written before we start. Every price change arrives as a written change order before a nail moves, because an allowance that isn’t on paper is a surprise waiting for a date. Labor and parts are quoted line by line. The finished work carries our 90-Day Done Right Promise in writing, and a live person answers the phone around the clock.
DIY or Call Us?
You can safely do a few things yourself. Photograph the label inside the cabinet. Measure door and drawer fronts. Tighten a loose hinge screw with a longer screw as a short-term fix. Clear hair and grit out of a drawer glide. If those solve it, you’ve saved yourself a service call and that’s fine by us.
Where it goes wrong: replacing a hinge or glide set on a door that then won’t align, ordering a part that doesn’t match your series, or chasing a water-damaged toe kick that hides a slow leak behind it. Bathroom cabinetry sits close to plumbing and electrical in most Fremont layouts, and pulling a vanity or opening a wall near a supply line isn’t a weekend project. If a leak has softened the panel, stop and call. We’ll talk you through what you’re seeing. Reach us at (833) 620-6162.
FAQs

Expect 15 – 25 years for the boxes and 10 – 15 years for hinges and glides under daily bathroom use. Fremont’s dry summers and damp winters stress the finish near wet zones faster than in drier climates, so seal edges and fix small leaks early.
Often yes. A stripped hinge screw can sometimes be filled and re-drilled, and worn hinges or glides can be swapped without touching the door. Once the panel has swollen or the finish has lifted, replacement is the honest answer. Call (833) 620-6162 and we’ll tell you which one you’re looking at.
A hardware or door swap is usually one visit; a full KraftMaid bathroom remodel runs three to six weeks depending on tile, plumbing and inspections. Permits and scheduling drive the timeline, not the parts.
We match from the series label inside the cabinet and confirm measurements before ordering, then choose OEM for visible fronts and quality aftermarket for hidden hardware. No warehouse stock on our end; the part gets matched to your model, not pulled off a shelf.
If your bathroom is due for more than a hinge, Barrett & Sons Construction Fremont pulls the permits, writes every scope and allowance down, and puts a name and address behind the license. Call (833) 620-6162 for a free estimate, or to get a straight answer on that sagging door before you spend anything.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












