







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cambria Home Additions & ADU: The Fremont Owner’s Guide
A Cambria-surfaced addition or ADU in Fremont typically runs $45,000 – $130,000 for a home addition, and $90,000 – $220,000 for a full accessory dwelling unit, depending on square footage, foundation work, and how much Cambria surfacing goes into the kitchen and bath. When a Cambria top in an addition starts to fail, the owner usually spots it the same way: a hairline crack near the sink cutout, a dull gray ring that won’t buff out, or a seam that’s started to shadow. What looks like a part failure is almost always an installation or substrate problem, and that’s the conversation worth having before anyone quotes you a replacement.

We install Cambria-compatible additions across Fremont, and our crew members have up to 28 years of experience with stone and slab work. Barrett & Sons Construction is an independent service provider, not affiliated with Cambria.
Which Cambria Models This Applies To

Cambria is engineered quartz, not natural stone, and every slab shares the same basic composition: roughly 90% quartz by weight bound in polyester resin. That matters for a Fremont addition because it means the “model” question is really about slab series and thickness, not some mechanical part that wears out. Cambria’s current lines – the marbled designs, the veined looks, the solid and speckled styles – all come in 2cm and 3cm thicknesses, and the thickness is what determines where a slab can be used without a substrate.
Here’s the compatibility gotcha most Fremont owners don’t hear until it’s too late: 2cm Cambria needs a full substrate and edge build-up on any countertop that overhangs past 6 inches, while 3cm can span further with proper support. If you’re matching new Cambria to an existing piece in your addition, match the thickness first, then the design. A 2cm slab sitting next to a 3cm slab shows at the seam no matter how good the fabrication is.
To identify what you have, look for the Cambria stamp on the underside of the slab and the fabrication sticker, and measure the exposed edge with a tape. Cambria doesn’t publish a per-slab serial database the way appliance makers do, so a fabricator matches by thickness and design name from the sample library. On the OEM-vs-aftermarket question: there’s no meaningful aftermarket for Cambria itself, but there is for the support layers under it – the plywood substrate, the sink clips, the seam adhesive – and that’s where cheap materials cause most of the failures we’re called out to fix.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Cambria Home Additions & ADU Is Failing
Cambria doesn’t fail on its own. The layer under it does, and the stone tells you about it. Watch for these:
- A hairline crack radiating from a sink or cooktop cutout. That’s a substrate gap or a missing support rail under the cutout, and it’s the most common Cambria failure we see in Fremont additions where the cabinet run wasn’t shimmed flat before the top went down.
- A dark ring or cloudy patch that won’t clean off. Cambria’s resin surface is non-porous, so a stain that won’t lift usually means oil or dye got into a seam or a micro-chip at the edge, not into the stone body.
- A seam that’s shadowing or feels raised to the fingernail. Seam adhesive shrinks and the two slabs shift against each other when the cabinets settle – common in older Fremont homes where the floor isn’t perfectly level under a new addition.
- A dull, chalky finish in one zone. Abrasive cleaners and heavy scrubbing strip the factory polish. Cambria can be re-honed, but only by someone who knows quartz, not by a general handyman with a buffer.
- A separation between the top and the backsplash or wall. That’s movement, not a cosmetic gap. In a Fremont addition it usually traces back to framing or cabinet movement that needs to be corrected before the stone is reset.
Replacement Cost & What’s Included
Here’s how the Cambria work breaks down in Fremont, installed, with labor and materials included:

| Scope | Installed Price Range |
|---|---|
| Countertop installation (Cambria, standard run) | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation (Cambria top) | $3,000 – $10,000 |
| Bathroom vanity installation | $800 – $3,000 |
| Home addition (full scope) | $45,000 – $130,000 |
| ADU construction (full scope) | $90,000 – $220,000 |
What drives the range on a Cambria piece: slab thickness (2cm vs 3cm), number of cutouts, edge profile, and how much substrate repair is needed before the new top goes down. We write the scope, the allowance, and any change order in writing before work starts – the price you see on the estimate is the price on the invoice. Every capable job gets permits pulled and inspections signed, and the work is covered by our written 90-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some checks are safe to do yourself. You can slide a straightedge across the countertop to spot a low spot, look for gaps under the slab at the sink cutout, test a dull patch with a damp cloth to see if it’s polish loss or residue, and measure the slab thickness with a tape. If the crack is visible to the eye, or a seam is raised or shadowing, stop there. Cutting, resetting, and re-seaming Cambria is not a homeowner job – a slip with a blade or a dropped slab can send sharp quartz edges somewhere that ends in an emergency room visit, and re-bonding a seam wrong the first time makes the second repair cost more. Call us at (833) 620-6162 and we’ll walk you through what we can see.
FAQs

Cambria is engineered quartz and typically lasts decades in a properly installed countertop – the stone body itself doesn’t wear out. What fails first is the layer under it: substrate, seam adhesive, and clips. That’s why the install matters more than the slab.
Often yes, if the crack is short and hasn’t separated the slab. We can re-seam or fill a hairline crack and re-polish the surface, but a crack that runs through a cutout or a full-slab split usually needs a replacement piece. Call (833) 620-6162 and we’ll tell you which one you’re looking at.
A single countertop run or vanity top is typically a one-to-two day job once the slab is fabricated and delivered, and fabrication adds a week or two on top of that. Larger addition work is scoped separately. Call for an exact timeline.
Through the Cambria fabricator network – we match slab thickness and design name to what’s already in your addition, and we verify the thickness before anything is ordered. We don’t carry parts on a truck; the material comes from the fabricator when the job is ready. Call (833) 620-6162 for a free estimate.
Get a Straight Answer on Your Cambria Addition
We’re a Fremont name with our license number, address, and name published – look it up before you sign anything. We also work with KraftMaid, Silestone, and Kohler when your addition needs cabinetry, a different quartz, or plumbing fixtures to go with the Cambria. Ask anyone on your street, or call us at (833) 620-6162 to schedule your free estimate. A live person answers 24/7.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












