







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Fremont Owner’s Guide
We build and finish home additions and ADUs in Fremont using Schluter systems for the waterproofing and tile assemblies, with typical additions running $45,000 – $130,000 depending on size, foundation, and how much of the wet area gets tiled. This is planned construction, so nothing happens same-day; what we do give you is a written scope, a written allowance schedule, and a firm sequence before the first form board goes down.

Owners usually discover a Schluter problem the slow way. A shower floor in a new addition starts feeling soft at one corner. Grout along the linear drain turns dark and won’t come clean. A hairline crack walks across the shower bench after two winters. Nine times out of ten the conversation starts the same way: “The tile looks fine, but something’s wet behind it.” That’s a waterproofing failure, not a tile failure, and on an addition it’s expensive because the fix reaches back into the framing and the inspection sequence.
Which Schluter Models This Applies To

The two assemblies we deal with most in Fremont additions are Schluter KERDI-BOARD panels (the foam tile backer used for shower walls and benches) and the KERDI-LINE linear drain system, along with DITRA-HEAT for heated floors in ADU bathrooms. KERDI-BOARD comes in thicknesses from 1/2 inch to 2 inch; the 1/2 inch is standard for walls over framing, and 2 inch is what we use to build a bench or a niche without framing it out. Getting the thickness wrong is the most common compatibility mistake we see. A 1/2 inch panel where the plan called for 2 inch throws off every fixture rough-in downstream, and by then the plumber’s already gone.
On the drain side, KERDI-LINE is a bonded waterproofing linear drain that has to be set into the same continuous membrane as the floor. It is not a drop-in replacement for a standard clamping drain, and the flange geometry has to match the shower’s subfloor prep. If your model number is on a sticker inside the drain body or on the KERDI-BOARD edge print, read it before you order anything. OEM Schluter components and quality equivalents differ mainly in the fleece bonding and the certified thickness tolerance, and on a project that has to pass a Fremont inspection, we stay with the OEM part. We don’t stock parts and nothing rides on a truck; we source what the job needs, matched to the model.
Barrett & Sons Construction Fremont is an independent contractor. We’re not affiliated with Schluter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
- Grout that darkens and won’t dry. Moisture is wicking through a compromised seam rather than staying on top of the membrane. The joint at the floor-to-wall transition and the drain flange are the first places to check.
- A soft or hollow-sounding shower floor. That hollow note means the membrane has lost bond to the substrate. On an addition over a slab or a framed floor, it usually traces back to prep, not product.
- Efflorescence or white crust on the tile or grout. Salt deposits mean water is moving through the assembly and evaporating at the surface. In Fremont’s dry summers it can stay hidden for months and then show hard in January.
- Cracked tile along a bench or curb. Movement, not grout wear. A bench built from KERDI-BOARD that wasn’t fully bonded and banded will flex just enough to crack a tile over a couple of seasons.
- Water staining on the ceiling or wall below the addition’s bathroom. This is the one that stops being a tile problem and becomes a framing and drywall problem. It means the membrane has been failing quietly for a while.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Repairing or rebuilding a failed Schluter wet assembly inside a Fremont addition typically runs with the scope, not as a flat part swap. A localized shower floor redo with new membrane and drain sits in the lower range; a full wet-area rebuild with new KERDI-BOARD, waterproofing, and tile runs several times that. For pricing context, additions as a whole are $45,000 – $130,000 in Fremont, a bathroom remodel inside one runs $9,000 – $28,000, a walk-in shower install $4,500 – $12,000, and a tub-to-shower conversion $3,500 – $10,000.
What drives the number up: whether the bench has to come out, whether the drain is set in a slab, and whether the framing behind the board is wet. Parts-plus-labor is quoted line by line, so you see the membrane, the drain, the board, and the labor as separate lines instead of one lump. Every job that’s eligible gets permits pulled and inspections signed. Every completed job carries our 90-Day Done Right Promise, written on the contract.
DIY or Call Us?
You can safely check a few things yourself. Look for the model print on the KERDI-BOARD edge or the sticker inside the drain body, press a dry paper towel into the corners of a shower floor and see if it wicks, and note whether the grout discoloration is at the drain flange or the wall transition. That tells you which assembly is likely failing and helps when you call.
What we don’t recommend is tearing into a wet assembly to check for yourself. KERDI-BOARD is a bonded system; once you cut it, you’re committing to a rebuild of the whole waterproofed area, not just the panel you pulled. There’s also a plumbing and permit layer here that most homeowners underestimate, and an inspector is going to look at the repair. If you’ve already got a soft floor or a stain below, call us at (833) 620-6162 and we’ll take a look before you open anything up.
FAQs

A properly installed KERDI system on a Fremont addition should last the life of the tile, easily 20 to 30 years, with the caveat that our local clay soils and slab movement put more stress on the floor-to-wall seams than a lot of other places. What fails first is almost always a seam or the drain flange bond, not the board itself. If yours is past 10 years and starting to show grout discoloration, it’s worth having it looked at before it reaches the framing.
Sometimes, yes. A localized failure at a drain flange or a single wall seam can be repaired by cutting back to sound membrane, re-bonding, and re-tiling that area. A broad soft floor or water staining below the addition usually means a full rebuild. We won’t guess on this; we take a look and tell you which it is before quoting. Call (833) 620-6162 for a free estimate.
A localized shower floor repair is usually a few days once we have the right parts; a full wet-area rebuild inside an addition runs a couple of weeks depending on tile and inspection scheduling. We give you the sequence in writing with the estimate, so you know what happens each day and when the Fremont inspector is coming. Call (833) 620-6162 to schedule your free estimate.
We match the part to your model number, order the OEM Schluter component, and confirm it against the plan and the drain or board spec before it gets installed. We don’t carry stock and nothing comes off a truck; we source what the specific job calls for, which is why the model number matters. Call (833) 620-6162 and we’ll walk you through what to read off your assembly.
We also install KraftMaid, Cambria, and Silestone on the finish side of these projects when your addition or ADU includes a kitchen or bath. If you’re staring at a soft shower floor on an addition in Fremont, or planning one and want the waterproofing done right the first time, call (833) 620-6162 for a free estimate. Every price change gets a written change order before the work moves, and every eligible job is permitted and inspected.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












