







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Home Additions & ADU: The Fremont Owner’s Guide
We build and finish Boral-spec home additions and ADUs for Fremont homeowners, with typical installed projects running $45,000 – $130,000 for an addition and $90,000 – $220,000 for a detached ADU. If your Boral trim, siding, or roofing components are failing at a seam, delaminating at the joint, or pulling away from the fastener line, you already know something isn’t right. It usually starts with a hairline crack at a joint nobody paid attention to, then water gets in during the first real winter rain off the bay, and by spring you’re looking at rot behind the material. That’s typically when Fremont owners call us.

Which Boral Models This Applies To
Boral makes several lines that show up in Bay Area additions and ADUs: Boral Siding, Boral TruExterior Trim, Boral Versetta Stone, and their cultured stone veneers. Each has its own fastener pattern, expansion tolerances, and thickness specs, and the part that fails on one won’t be the part that fails on another. Before we quote anything, we read the label on the back of the piece or measure the profile. On TruExterior, for example, the pieces are engineered poly-ash, and they expand and contract differently than wood or fiber cement – that matters when we’re matching a replacement to existing run. On the OEM-versus-aftermarket question: for Boral profiles, we go OEM when the profile is exposed and visible; aftermarket equivalents from a manufacturer like Versetta can work on hidden runs, but you’ll see the difference at the corner. We’re an independent contractor – not affiliated with Boral. We also work with KraftMaid, Cambria, and Silestone for the interior finishes on these projects.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Home Additions & ADU Is Failing
- Hairline cracks at seams or joints. Usually thermal movement that the original install didn’t leave room for. Boral TruExterior needs a gap; if it was butted tight, the crack was nearly inevitable.
- Delamination or peeling finish. Often a moisture problem at the edge or a factory finish that took UV damage. In Fremont it shows up on south-facing walls first.
- Fastener pull-out or loose panels. Fasteners set too close to the edge or into wet substrate. On a recent addition in the Irvington district, we found fasteners backed into OSB that had been wet since framing.
- Rot behind trim or at the kick-out. Water gets in through a missing kick-out flashing, sits behind the material, and destroys the substrate before you see it from the outside.
- Visible color or texture mismatch after a repair. Someone tried to patch with an off-brand product. Boral cultured stone especially won’t match aftermarket look-alikes, and the difference reads from the sidewalk.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a Boral trim or siding component repair or replacement on an addition or ADU in Fremont, most jobs run from a few hundred to a few thousand dollars, depending on how much substrate needs to come off and whether the damage has reached the framing. Full addition projects, when the failing Boral component is part of a broader rebuild, fall in our lead range of $45,000 – $130,000. Detached ADUs run $90,000 – $220,000.
What drives the number: material type, linear feet, whether we’re replacing a few pieces or re-siding a wall, substrate condition, and how accessible the work area is. Every scope comes in writing before we start. If we open the wall and find rot, you get a written change order with the price – not a surprise invoice at the end. The work is backed by our 90-Day Done Right Promise.
DIY or Call Us?
You can safely inspect the outside of the material – look for cracks, caulk pulling away, or visible gaps at joints – and take a few photos. What you shouldn’t do is pull siding or trim to check what’s behind it on an addition or ADU. On Fremont homes, that’s where you find out whether the waterproofing is intact, and if it isn’t, opening it yourself can let in water that wasn’t there before. The other thing to avoid is patching with a product that won’t match – Boral’s finishes are specific, and matching them takes someone who knows the line. If it’s failing, call us at (833) 620-6162 for a free estimate. We’ll tell you honestly whether it’s a small repair or a bigger problem.
FAQs

How long should a Boral component last on a Fremont addition? Boral’s engineered products are rated for decades of service in a normal climate, but the real answer is how well it was installed. Missing kick-out flashings and tight joints will cut lifespan shorter than the material’s rating. Call (833) 620-6162 if you’re seeing early failures.
Can this be repaired instead of replaced? Sometimes, yes. A cracked seam or failed caulk joint can often be stabilized. If the material is delaminating or the substrate is wet, replacement is the honest answer. We diagnose it before quoting.
How long does the replacement take? A small component repair is typically a half-day to a day. Larger runs on a wall can run two to four days depending on weather and access. We’ll give you a written timeline with the scope.
How do you source the Boral part? We source through Boral’s dealer network to match the exact profile and finish. If the specific profile has been discontinued, we’ll tell you up front and discuss aftermarket options with a clear picture of the visual difference. Call for a free estimate.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












