







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Therma-Tru Windows & Doors: The Fremont Owner’s Guide
We install and service Therma-Tru windows and doors for homeowners across Fremont, and a full door entry system replacement typically runs $4,500 to $15,000 installed depending on door count, series, and whether the rough opening needs correction. Most failed hardware on a Therma-Tru door can be swapped in a single afternoon, and we schedule those repairs inside a normal week. Impact-rated window installations in Fremont fall in the $8,000 to $25,000 range.

Most owners discover a failed part the same way. The deadbolt stops catching without a hip-check. The multipoint lock grinds halfway down. The hinge leaf sags and the door corner starts rubbing the threshold. Therma-Tru builds a solid door, but the moving hardware on a Fiber-Classic or Smooth-Star entry sees thousands of open-and-close cycles over a California decade, and one component always wears out before the rest. This page is built for the Fremont owner who already knows which part is failing and wants it matched, priced honestly, and installed by someone who answers his own phone.
Which Therma-Tru Models This Applies To

Therma-Tru’s residential line covers three families Fremont homeowners call us about most: Fiber-Classic and Smooth-Star entry doors, the Classic-Craft premium line, and the fiberglass and steel patio and sidelite systems. The door leaf rarely fails. The hardware does. Hinges, multipoint lock assemblies, deadbolts, weatherstripping, sweeps, bottom rails, and sidelite framing are the parts we replace and the parts we quote.
Finding the right part starts with the label. Therma-Tru stamps a model and series number on the hinge edge of the door slab and inside the jamb on the lock side. Photograph both. Measure the door height and width at the slab (not the frame), then measure the lock backset center-to-edge. A 2-3/8″ backset and a 2-3/4″ backset use different hardware, and getting that wrong is the most common Therma-Tru parts mistake we see in Fremont. A few Fiber-Classic series changed hinge prep spacing between production runs, so an OEM replacement hinge may or may not drop into your existing mortise.
OEM Therma-Tru hardware is the safest match for anything on a multipoint lock. Aftermarket equivalents work well for standard hinges, sweeps, weatherstripping, and finish touch-ups, and often cost 30 to 50 percent less. We’ll tell you which side of that line your part sits on before you buy anything. Barrett & Sons Construction Fremont is an independent service provider and is not affiliated with Therma-Tru.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Therma-Tru Windows & Doors Is Failing
- The door sags and rubs the threshold. Hinge leaves bend or screws lose bite in the jamb over time. Left alone, the slab starts wearing the finish off the bottom rail.
- The multipoint lock grinds or won’t fully engage. The lock gearbox or the extension rods are worn or out of alignment. This is a security issue and the most common emergency repair we handle on Therma-Tru entries in Fremont.
- Daylight shows around the door or sidelite. Weatherstripping has compressed and lost its spring. In Fremont’s dry summers and damp winters, that gasket takes a beating.
- Water tracks inside the bottom rail or on the sill. The door sweep or sill pan has failed, or the frame has shifted. Left alone, a fiberglass door with a saturated bottom rail is expensive to save.
- The glass seal fogs between panes. The insulated glass unit has lost its seal. This is a glass replacement, not a door replacement.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what Therma-Tru work runs in Fremont, installed and cleaned up:
- Entry door hardware swap (hinges, lockset, deadbolt): $180 to $650
- Multipoint lock or gearbox replacement: $280 to $900
- Weatherstripping and sweep replacement: $120 to $400
- Therma-Tru door slab replacement (hardware reused): $1,200 to $4,500
- Full Therma-Tru entry system replacement with frame: $4,500 to $15,000
- Impact window installation (Therma-Tru and comparable lines): $8,000 to $25,000
The price range moves on three things: door series, hinge prep complexity, and whether the rough opening needs correction when we pull the old unit. Every scope and every allowance comes to you in writing before we touch the door, and any change arrives as a written change order. Every eligible job gets permits pulled and inspections signed, because the last contractor most owners used told them permits were optional. Every completed job carries our 90-Day Done Right Promise in writing.
DIY or Call Us?
A Fremont homeowner can safely photograph the door label, measure the slab, note the backset, and check for stripped hinge screws or loose lock plates. All of that helps us match the correct Therma-Tru part on the first try.
Where DIY goes wrong: multipoint lock alignment. The rods are keyed to factory tolerances, and a hand-adjusted gearbox that’s 1/16″ off will leave the door impossible to lock from outside the next time the weather shifts. Same story with a sagging Fiber-Classic slab on a two-panel hinge set; homeowners bend hinge leaves trying to lift the corner and end up replacing hinges anyway. We’ve been doing this work since 1998, our technicians have up to 28 years of experience, and we carry the tools to reset a hinge mortise and re-hang a door square in one visit. Call (833) 620-6162 to schedule a free estimate.
FAQs

Standard Therma-Tru hinges and locksets typically run 10 to 15 years before repair or replacement in Fremont’s climate, and multipoint lock gearboxes often go 8 to 12 years. The dry summers accelerate weatherstripping wear faster than most owners expect, so we recommend checking the sweep and jamb gaskets every two years. Call (833) 620-6162 for an exact quote on yours; estimates are free.
Usually yes, if the door leaf and frame are sound. Hinges, weatherstripping, sweeps, locksets, and glass units can all be swapped without replacing the door. The one case where repair cost climbs past replacement is a fiberglass door with a saturated or rotted bottom rail. Call (833) 620-6162 and we’ll tell you which side of that line your door sits on.
Most single-part hardware swaps on a Therma-Tru entry take two to three hours. A full door slab replacement runs four to six hours. A full entry system replacement with frame is a one-day job for our crew in most Fremont homes. Call (833) 620-6162 to schedule an estimate and we’ll give you the timing in writing.
We match the part to your door’s model and series label, then source through licensed Therma-Tru distribution to confirm the correct spec before the part is ordered. That avoids the most common Fremont mistake: a backset or hinge-prep match that looks right on paper but won’t install. Bring us the label photo and measurements, and we’ll price the exact part. Call (833) 620-6162 for a free estimate. We also work with KraftMaid, Cambria, and Silestone on kitchen and bath projects in Fremont.
Barrett & Sons Construction Fremont is owner-operated by Tom Barrett and his sons, with the name, address, and license number published so you can look them up before you sign anything. Every eligible job includes permits pulled and inspections signed, every price change in writing, and the written 90-Day Done Right Promise. A live person answers the phone 24 hours a day, 7 days a week. Current standing offers: $40 off any repair over $200, free second opinion on any written estimate, no trip charge inside the county, and a permanent 10% Senior & Veteran discount.
Call (833) 620-6162 today to schedule your free estimate on your Therma-Tru part in Fremont. We answer live, we quote in writing, and we show up when we say we will.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












