







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Kitchen Remodeling: The Fremont Owner’s Guide
We install Barrette kitchen components and refit failed Barrette parts across Fremont, and a full Barrette kitchen remodel runs $14,000 – $45,000 installed, with single-part repairs priced line by line. We’re an independent construction company, not affiliated with Barrette; we source genuine Barrette replacement parts and measure-fit equivalents when a model line has been discontinued.

Owners in Fremont usually find a Barrette problem the same way: a cabinet door that won’t stay shut past 80 degrees, a drawer that grinds halfway out, a hinge plate pulling loose from particleboard that took on moisture during the rainy season. Barrette parts are matched to a model number, not a shelf size, so the first move is identifying exactly what you have before anyone quotes you a number. Kitchen Remodel starts at $14,000 and climbs with cabinet runs, island work and countertop changes.
Which Barrette Models This Applies To

Barrette builds kitchen cabinetry and door lines in several series, and the part you need depends on which series your kitchen carries. The fastest way to identify it is the model and series label inside the cabinet box, usually on the back of a drawer box or the inside of a cabinet door. Photograph it. Barrette has retired several series over the years, and a discontinued door profile won’t accept a current hinge; that mismatch is the single most common compatibility gotcha we see in Fremont kitchens.
Two checks matter. First, hinge cup bore: 35mm is standard, but older Barrette doors sometimes ran a shallower bore that a modern clip-on hinge won’t seat in without a plate change. Second, drawer glide length and mounting pattern: 15-inch and 18-inch glides are not interchangeable, and the screw pattern differs between undermount and side-mount versions. On OEM versus aftermarket, genuine Barrette parts match your finish and drilling exactly. A quality aftermarket glide from a known maker will outlast a cheap OEM replacement, but confirm the mounting pattern before you buy. KraftMaid, Cambria and Silestone jobs we handle too, so we’re used to matching parts across brands.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Kitchen Remodeling Is Failing
- Doors that drift open on their own. The hinge spring has lost tension or the cup screws have stripped their bite in the door. In Fremont’s dry summers, particleboard shrinks and screws loosen faster than owners expect.
- Drawers that grind or jump the track. A worn glide roller or a bent track. Once the nylon wheel flattens, no amount of adjusting brings it back.
- Sagging shelves or a bowed cabinet bottom. The shelf pin has pulled through or the bottom panel took on moisture near the sink. This one gets worse quietly.
- Loose hinge plates at the cabinet frame. Screws spinning in stripped holes. A bigger screw is a patch, not a fix, and it splits the frame eventually.
- Finish peeling at the door edges. Heat and steam near the range lift the laminate or veneer edge. It’s cosmetic until moisture gets under it, then the door core swells.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what the work runs in Fremont, parts and labor together:
| Job | Installed Range |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Kitchen island installation | $3,000 – $10,000 |
| Backsplash installation | $800 – $2,500 |
The range is driven by cabinet run length, whether the countertop is being replaced, and how much of the layout is moving. A single hinge or glide swap sits far under these numbers, and we quote it line by line: part, labor, disposal. Our technicians have up to 28 years of experience, and every price change reaches you as a written change order before the work moves. Every eligible job gets permits pulled and inspections signed, and the 90-Day Done Right Promise is written on the contract.
DIY or Call Us?
You can safely do the identification work: read the series label, photograph the hinge cup, measure the glide length, and note whether the door is 35mm bored. Swapping a drawer glide on a standard side-mount is also within reach if you match the pattern exactly. Where it goes wrong is stripped hinge plates in a cabinet frame, doors that need re-boring, and any job where the cabinet box itself has taken on water damage near the sink. We’ve watched homeowners chase a stripped screw with a larger screw three times and split the stile. Call us at (833) 620-6162 and we’ll tell you honestly whether it’s a ten-minute part swap or a cabinet repair, then schedule your free estimate.
FAQs

A quality Barrette hinge or glide typically runs 10 to 15 years before the spring or roller goes soft. Fremont’s wet winters and dry summers accelerate screw loosening at the frame and finish peeling near the range. Call (833) 620-6162 for a free estimate on replacing worn parts.
Sometimes, yes. A loose hinge plate can often be re-anchored with a proper insert rather than a new door, and a drawer glide can be adjusted before it fails completely. Once the door core has swelled from moisture or the cabinet frame is split, replacement is the honest answer. Call us and we’ll tell you which you’re looking at.
A single hinge or glide swap is often done in under an hour. A full set of cabinet doors or drawers is typically a half day to a full day, depending on count and whether any re-boring is needed. Call (833) 620-6162 to schedule and we’ll give you a realistic window.
We order genuine Barrette parts by model and series number off the label in your cabinet. If the series is retired and no OEM part remains, we measure-fit a quality equivalent and confirm the bore and mounting pattern before ordering. Call (833) 620-6162 and bring the label photo to your free estimate.
To get a straight answer on your Barrette kitchen, call Barrett & Sons Construction Fremont at (833) 620-6162 to schedule your free estimate. We publish Tom Barrett’s name, address and license number, and we’ll hand you a written line-item quote with any change order in writing before a nail moves. Ask about our Free Second Opinion on Any Written Estimate and our permanent 10% Senior & Veteran discount.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












