







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Ameristar Fence Installation: The Fremont Owner’s Guide
Ameristar fence installation in Fremont typically runs $3,500 – $9,000 installed, depending on the series, total linear footage, gate count and whether we’re removing an old fence first. We handle Ameristar-compatible ornamental aluminum, steel and vinyl systems, and every quote comes as a written line-item scope before any work begins. Most Fremont projects get scheduled within a week or two of the estimate.

Owners usually call us after a wind event or a gate they’ve been meaning to fix for two seasons. In Fremont’s older neighborhoods around Niles and Centerville, a post that’s been leaning since the last atmospheric river is the most common first sign. Then there’s the gate that scraped the driveway all winter. Somebody finally notices the hinge plate has pulled clean out of the post. That’s usually when the phone rings.
Worth saying up front: Barrett & Sons Construction Fremont is an independent contractor. We install and service Ameristar fence systems, but we’re not affiliated with or endorsed by Ameristar Fence Products.
Which Ameristar Models This Applies To

Ameristar builds a lot of residential product, and getting the model right matters more than people expect. Their core ornamental aluminum lines (Montage, Transced and similar) use extruded aluminum rails and pickets with a baked-on powder coat. Their steel systems use galvanized frames, which behave differently in coastal air. Vinyl systems use specific rail profiles that don’t swap between series.
To identify what you’ve got, look for the manufacturer’s label, usually a sticker inside the top rail, on the inside face of a post, or tucked under a hinge plate. No label? Measure the picket width, the rail height and the gap between pickets. Those three numbers usually point to the right series. Bring photos to the estimate, not just measurements.
On OEM versus aftermarket: Ameristar-branded replacement parts fit exactly and match the powder coat color, but they cost more and lead times can run several weeks. Quality aftermarket aluminum parts can work well when the wall thickness and alloy match, but cheap import pickets are thinner and they’ll dent in a way the original won’t. On a Fremont fence that’s exposed to bay winds, we don’t put thin-gauge aftermarket parts on a gate or a corner post. There’s no point saving forty dollars on a bracket that has to hold a fifty-pound gate.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Ameristar Fence Installation Is Failing
- Posts leaning after a storm. Usually a footing that wasn’t deep enough or concrete that was set in wet soil. In Fremont’s clay-heavy ground, a shallow post will move within a couple of seasons once the wet winter comes.
- Gates sagging or dragging. The hinge side has pulled out of the post, or the post itself rotated. Ameristar gate hardware uses specific hinge sets, and using a generic hinge speeds up the wobble instead of fixing it.
- Rust bleeding through at weld points or scratches. Powder coat is tough but it doesn’t heal. Any cut or chip in coastal air near Fremont will start to oxidize, and once rust creeps under the coating it lifts it off.
- Loose pickets that rattle in wind. Fasteners backing out of the rails, or rivets that have corroded. Ignore it and the picket works free and starts rubbing on the neighbor’s car.
- Gate latch or striker no longer catching. The post has shifted out of square, not the latch failing on its own. Replacing the latch alone will just postpone the problem a few months.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a full Ameristar fence installation in Fremont, expect $3,500 – $9,000. A short run of ornamental aluminum on a standard lot tends to land near the lower end. Longer runs, multiple gates, slope work, or a full tear-out of an old chain-link or wood fence push toward the top of that range.
| Line item | Typical Fremont range |
|---|---|
| Ameristar-style aluminum fence, installed | $3,500 – $9,000 |
| Section repair (damaged panel or post) | Quoted per section, parts plus labor |
| Gate hinge or latch replacement | Quoted per gate |
| Old fence tear-out and haul-away | Folded into the quote, itemized in writing |
| Permit (if required by the City of Fremont) | Pulled by us, listed on the estimate |
Costs move based on linear footage, height, gate count, slope, soil conditions and access. On slopes, footings have to be stepped, not just set at one depth. Fence height rules in Fremont can vary by zone and HOA, so the permit check matters. Every scope and every allowance shows up on paper before we start, and every change gets a written change order first. The finished work carries our written 90-Day Done Right Promise.
DIY or Call Us?
Owners can safely do a few things. Walk the line and check for loose fasteners. Note which posts move when you lean on them. Photograph every label and every damaged part. Write down the linear footage and gate count. That’s useful information.
Where it goes wrong: digging and setting new footings. A post that’s not set below the frost line in Fremont’s clay will heave again by the second winter. Gate rehanging is the other common trap, since Ameristar hinges need specific alignment and most homeowners over-tighten or mount to a post that’s already out of plumb. Meanwhile the gate keeps tearing itself loose. There’s no safety hazard in fence work the way there is with a garage spring or a live panel, but a bad footing is an expensive lesson to learn twice. If you want a straight answer on whether a repair or a replacement makes more sense, call (833) 620-6162.
FAQs

Ornamental aluminum systems usually last 20 to 30 years in this climate. Powder coat and powder-coated galvanized steel hold up well, but coastal air near the bay speeds oxidation on any cut edge or scratch. Washing the fence once or twice a year and touching up chips early is what gets you to the far end of that range.
Often, yes. A single damaged panel, a bent gate frame or a failing hinge can usually be replaced on its own, and the rest of the fence stays. When posts are moving or the footings are failing, the repair doesn’t hold, and we’ll tell you straight if that’s the situation. Call (833) 620-6162 for an honest assessment.
A single section or gate repair is usually a few hours. A full Ameristar fence installation on a typical Fremont lot takes a couple of days, sometimes longer if there’s tear-out or significant slope work. We’ll give you a realistic schedule on the written estimate, not a guess over the phone.
We identify the series from the label or from on-site measurements, then order the matching part from the manufacturer or a verified aftermarket supplier. There are no mystery parts and nothing pulled off a van. When the part arrives, it matches the original in size and finish.
Only if the scope changes, and then only with a written change order you approve before anything moves. What’s on your estimate is what you pay unless something real is uncovered underneath, and we walk you through it first.
If you’re pricing an Ameristar fence installation or a part-specific repair in Fremont, the fastest path is a phone call. We’ll pull together a written line-item estimate, tell you whether repair or replacement makes more sense, and hand you a name and a license number you can verify. Call (833) 620-6162 for a free estimate. We also work with quality brands across the trades, including KraftMaid, Cambria and Silestone, so if something else around the house needs attention, ask us while we’re there.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












