







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cambria Fence Installation: The Fremont Owner’s Guide
Barrett & Sons Construction installs Cambria-compatible fence systems in Fremont, and a typical installed project runs $3,500 – $9,000 depending on linear footage, grade, and gate count. If you’re pricing a repair instead of a whole run, most failed hardware and post issues fall inside that range on the lower end. We’re an independent contractor and not affiliated with Cambria, so we’ll tell you plainly what’s worth fixing and what’s worth replacing.

Owners around Fremont usually find the problem the same way. A gate starts dragging in the wet months. A post leans a half inch after a dry summer. Or a panel that held up fine for years suddenly racks sideways, and you can’t get the latch to line up no matter how many times you adjust the hinges. That’s the moment the phone comes out.
Which Cambria Models This Applies To

Cambria builds fence systems across several product families, and matching the right replacement hardware or panel profile to your line matters more than most homeowners expect. The two things that trip people up are post gauge and panel infill thickness. A 2-inch post and a 2-1/2-inch post can look identical from the street, but caps, brackets, and hinge plates don’t swap between them. Measure the actual post, don’t trust the old bracket as a reference.
To identify your line, check the inside face of a gate post or the bottom rail. Most Cambria systems carry a sticker or stamped mark with the series and the year of manufacture. Take a photo of it before anything gets pulled apart. If the label’s gone, measure the post outside diameter, the rail channel width, and the panel thickness with a tape. Those three numbers will pin down the profile in almost every case.
On OEM versus aftermarket: for gate hardware and fastener kits, quality aftermarket equivalents hold up fine and often cost less. For structural brackets and proprietary post caps, we recommend staying with the Cambria-spec part. The tolerances are tighter than they look, and a bracket that’s a hair off will work loose first in Fremont’s clay soils, where the ground moves with every wet winter and dry summer.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Cambria Fence Installation Is Failing
Fence failures show up in a predictable order. Watch for these five:
- Gate sag that keeps coming back. You tighten the hinges, it holds for a month, then drops again. That’s usually a hinge plate pulling out of soft wood or a post that’s lost its footing, not a hinge problem.
- A post that leans after rain. Clay-rich soil around Fremont swells in winter and shrinks in summer. A post set too shallow will walk with that cycle until it settles at an angle.
- Panels that rack out of square. If the top rail and bottom rail aren’t parallel anymore, the panel has lost its fasteners or the post spacing has shifted. Racking means the whole run is under stress.
- Loose brackets and rattling hardware. Wind load here is mild, so rattling usually means fasteners have backed out. Left alone, the bracket wallows out the hole and the post needs repair, not just a new screw.
- Rot or split at the post base. The bottom 12 inches take the most moisture. A split at the base is the first sign the post is on its way out, even if the top still looks solid.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

In Fremont, Cambria-compatible fence repair and installation runs $3,500 – $9,000 for a typical residential run. Here’s what moves you toward one end or the other:
- Linear footage and gate count: the biggest driver. A long run with two gates sits near the top of the range.
- Post replacement: resetting or replacing posts adds labor because of excavation and soil conditions.
- Grade and slope: a sloped yard needs stepped panels, which take more time than a flat run.
- Parts selection: OEM structural hardware costs more than aftermarket, and we’ll quote both so you can decide.
Every estimate is a written line-item quote. Parts and labor show separately, and if the scope changes once we’re on site, you get a written change order before any work proceeds. We pull permits where the job requires it and get inspections signed, and the finished work is backed by our 90-Day Done Right Promise.
DIY or Call Us?
Some checks are safe and worth doing yourself. Walk the run and note where posts lean, photograph any labels, measure the post diameter and panel thickness, and test the gate swing with the latch open. That tells you whether you’re looking at hardware or structure.
Where DIY goes wrong is the structural side. Digging out and resetting a post at the right depth in Fremont’s clay is harder than it looks, and a post that’s not set deep enough will lean again by the next wet season. Panel replacement on a racked run needs the whole section brought back to square, which takes two people and the right bracing. If a gate is hanging off a failing post, that’s a fall hazard and a security gap, and it’s worth having it done right. Call us at (833) 620-6162 and we’ll walk you through what you’re seeing before you commit to anything.
FAQs

Most Cambria fence systems hold up 15 to 25 years in this climate, with the posts being the first thing to go. Fremont’s wet winters and dry summers work the soil, so post footing is the weak point, not the panels. Gate hardware may need replacing sooner, usually every 7 to 10 years.
Often yes, especially if the failure is hardware, a single post, or one racked panel. A full run only needs replacing when multiple posts have failed or the frame itself is compromised. We’ll tell you honestly which one you’re facing after we look at it.
A single post reset or hardware swap is typically a half-day to a full day. A full run replacement usually takes two to four days depending on footage and gate count. We’ll give you a realistic schedule in the written estimate, not a number designed to win the bid.
We match the part to your series using the labels, measurements, and model info you provide, then order the OEM or approved aftermarket equivalent. We don’t carry parts on a truck, so we order what your fence actually needs. Call (833) 620-6162 for a free estimate.
If your Cambria fence in Fremont is failing, or you’re planning a new run and want it done to spec, give us a call. We also install KraftMaid, Silestone, and Kohler products across our other trades. Barrett & Sons is owner-operated, every eligible job gets permits pulled and inspections signed, and every price change arrives in writing before work starts. Call (833) 620-6162 to schedule your free estimate.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












