







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Fence Installation: The Fremont Owner’s Guide
Fence installation in Fremont runs $3,500 to $9,000 for a typical CGI residential job, and the number settles once we walk the line and see the grade, the gate count, and what’s buried at the posts. That’s not a phone quote. That’s a written scope with allowances and change orders before any digging starts.

Most Fremont owners don’t come to us because a fence is “failing.” They come because the last crew left a wobbly gate, a post set in sandy Bay Area soil that leans by the second winter, or panels that warped in the heat. Others bought a CGI-style system from a big-box run and now need it set right. We’re an independent contractor, not affiliated with CGI, but we install to manufacturer spec and pull the permits.
Which CGI Models This Applies To

CGI fence systems come in several product lines, and the fit depends on which one you’re holding. Identify your series by the stamped label on a post cap, a panel rail, or the hardware bag the original installer left in your garage. If that label is gone, measure post spacing (typically 6 or 8 feet center-to-center), panel height, and rail thickness. Those three numbers usually tell us the line.
OEM parts for CGI systems are the safest match. Aftermarket equivalents can work, but the post-to-rail connector and gate hinge geometry are where mismatches show up fast. We source OEM or a measured equivalent, never a guess. For our other trade brands, we do the same with KraftMaid, Cambria, and Silestone.
One more Fremont reality: coastal moisture and summer heat swing fence materials hard. A part rated for interior or dry-climate use will fail here in two or three seasons. We spec for the actual climate your fence lives in.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Fence Installation Is Failing
- Sagging gate that drags the ground. Usually a hinge or post-cap failure, not the gate itself, and the fix is a hinge replacement or a post reset.
- Leaning posts after winter rain. Fremont’s clay-heavy soil and pooling at the base shift posts that weren’t set deep enough or in proper footing. Re-excavation and re-set fixes it.
- Loose rails or popping connectors. The post-to-rail hardware has worked free. This one often lets you see it before the panel falls.
- Warped or split panels. Heat cycling on a CGI line rated below the local exposure. Replacement with a correct-grade panel is the honest fix.
- Rust streaks at the base plate. Galvanized or coated hardware breaking down from wet-dry cycles. Swap the hardware, not the whole fence.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

CGI fence installation in Fremont is $3,500 to $9,000 for a standard residential run. What moves the number: linear feet, gate count, grade and slope, footing depth, and whether old fencing must come out first. Every job includes a written scope, an itemized allowance for hardware, and a written change order before any scope change. Permits are pulled and inspections signed where Fremont requires them.
Here’s a rough line-item feel, Fremont-based:
- Post removal and reset with proper footing: $150-$350 per post
- Hinge and hardware replacement: $75-$200 per gate
- Panel replacement with correct-grade material: $200-$600 per panel
- Full run replacement (per linear foot, installed): $45-$90
Every completed job is backed by our written 90-Day Done Right Promise. If it’s not done right, one call brings Tom back to make it right.
DIY or Call Us?
You can safely check your own fence. Walk the line for lean, test gate swing, look at connector tightness, and photograph the label on any hardware you can find. What you should not do is dig out and reset a post footing or try to re-hang a gate on a failing hinge without knowing the load. Set a post wrong in Fremont’s soil and you’ll be back at it after the first rain, or worse, the panel comes down on someone.
Call (833) 620-6162 for a free estimate. We’ll tell you honestly whether it’s a $150 hardware swap or a full run.
FAQs

Ten to fifteen years for a properly installed, climate-matched CGI run; posts set in shallow or poor footings fail in two to three. Fremont’s wet winters and dry summers stress the base first, so footing depth matters more than panel grade.
Often yes. A sagging gate, a loose rail, or a single wobbly post is usually a hardware or footing fix, not a full replacement. We quote repair and full install side by side so you can see both.
Hardware or a single post is a half-day; a full residential run is one to three days depending on length, demo, and footing. Weather and gate count drive the schedule, and we tell you the timeline in writing up front.
We read the label off your existing hardware, match it to the manufacturer line, and source OEM or a measured equivalent. No guessing, and no stocked-parts-on-a-truck promise, because we don’t carry inventory.
Ready to stop guessing? Call Barrett & Sons Construction Fremont at (833) 620-6162 for a free estimate. A live person answers, 24 hours a day. We’ll look up the model with you, price it in writing, and pull the permits if the job needs them.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












