







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
GAF Bathroom Remodeling: The Fremont Owner’s Guide
A GAF bathroom remodel in Fremont typically runs $9,000 – $28,000 installed, with most full-gut jobs on a 1950s – 1970s ranch landing between $14,000 and $22,000 once you account for the surprises those homes hide. We schedule the walkthrough first and the work as soon as the drawings and permits clear, not the same day.

Fremont owners usually discover the problem the same way: a hairline crack spreads across the shower floor tile, or the ceiling below the upstairs bath starts showing a faint tea-colored ring after the first real rain of the season. Both trace back to the same root – a waterproofing assembly that never bonded to the substrate, or a drain flange that wasn’t set to the slope it needed. By then the framing behind the shower valve is soft, and the remodel just got real.
Key Takeaways
- Full GAF bathroom remodels in Fremont run $9,000 – $28,000; small baths land at $5,000 – $12,000.
- Waterproofing failures show first under the floor or on the ceiling below – check there before you replace tile.
- We’re an independent contractor, not affiliated with GAF. We install the system per GAF’s published detail specs.
- Every eligible Fremont job gets a permit pulled and inspection signed.
- Written change orders before any scope shift – no surprise invoice at the end.
Which GAF Models This Applies To

GAF makes three bathroom waterproofing systems you’ll run into in Fremont homes: the DensShield Tile Backer line (the gold and purple boards, 1/4″, 1/2″, and 5/8″), the DensDeck line for exterior or heavy-moisture assemblies, and their shower pan and drain assembly components. If your existing bathroom was tiled in the last fifteen years, the board behind it is very likely DensShield; pull the escutcheon plate off the shower valve and look at the cut edge – the gold face gives it away.
On the tile backer, DensShield is marked on the printed face with a batch code and the UL logo. Match that board to what’s already installed if you’re patching, because mixing DensShield with a generic cement board on the same wall creates a bonding problem where the two meet. For a full remodel we don’t patch – we tear out to studs and start fresh.
Here’s the compatibility gotcha most homeowners miss: DensShield is a 1/2″ nominal board, not a true 1/2″ – measure it if you’re trying to match existing tile height at a half-wall or a door opening, because a 1/16″ difference shows up as a lip on the threshold. On the OEM-versus-aftermarket decision, there’s no such thing as a GAF-equivalent aftermarket board – the acrylic-coated gypsum core is the GAF part, and a generic moisture-resistant drywall isn’t a substitute. Don’t let anyone tell you it is. Where aftermarket makes sense is on the smaller hardware: the drain grate, the valve trim, the escutcheon – those can come from a quality third party. Call us at (833) 620-6162 and we’ll tell you exactly what your existing assembly is.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your GAF Bathroom Remodeling Is Failing
The pattern in Fremont is consistent. Here’s what owners report and what’s usually underneath it.
- Hairline cracks in the shower floor tile, radiating from the drain. The pan beneath has lost its bond to the substrate, so the tile is flexing. Cracking is structural, not cosmetic, and it means water is getting past the surface.
- A water stain on the ceiling below the bathroom. Drain flange not seated to the slope, or the pan liner was never clamped properly. This is the one that ends a “just retile it” conversation fast – the framing gets wet before the stain appears.
- Grout lines turning dark and staying dark after cleaning. Moisture is wicking through from behind the tile because the backer board isn’t shedding water the way DensShield is designed to. Efflorescence – that white powdery bloom on grout – is the tell.
- Tile popping off the wall or feeling hollow when you tap it. Bond failure between thinset and the board face. Often the board was installed without the proper fastener pattern, or a generic MR board was used where DensShield belonged.
- A musty smell that doesn’t go away with ventilation. Mold in the wall cavity behind the shower. You can’t see it yet, but you can smell it, and the longer it sits the bigger the tear-out gets.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the pricing we quote in Fremont, and it doesn’t move once the change orders are signed.

| Scope | Installed Range (Fremont) |
|---|---|
| Full bathroom remodel (gut, new waterproofing, tile, fixtures) | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Bathroom vanity installation | $800 – $3,000 |
What drives the range: the condition of the framing once we open the wall, whether the drain location moves, how much tile you choose (the material line is the biggest swing), and whether the vent stack or supply lines need rerouting on a 1950s Centerville or Irvington home where copper has been sweating for decades. What’s included: tear-out, framing repair, the full GAF waterproofing assembly installed per the published details, tile setting, fixtures, finish carpentry, permit, inspection, and cleanup. Parts and labor are separated line by line on the written estimate so you see where the money goes. Every completed bathroom carries our 90-Day Done Right Promise in writing. Throw in the permanent 10% senior and veteran discount and the small-bath number gets friendlier.
DIY or Call Us?
What you can safely do yourself: pull the shower valve plate and look at the board’s printed face to identify it, tap the tile to listen for hollow spots, run the shower for ten minutes and watch the ceiling below, and check the caulk line at the floor for gaps. That’s a diagnostic, and it takes fifteen minutes.
Where DIY goes wrong: the waterproofing. A GAF-compliant shower pan is a multi-layer assembly – preslope, liner, flange clamp, backer board with the correct fastener spacing and joint treatment, then the setting bed. Each layer depends on the one below. Get the preslope wrong by even a quarter inch and water pools, finds the weakest point, and you’re tearing out fresh tile in two years. That’s a $4,000 mistake to save $1,800 in labor. Add in the 220-volt work if you’re putting in a heated floor and you’re past what a homeowner should touch. This is a planned remodel, not an emergency – we schedule the walkthrough, quote it in writing, and you decide. Call (833) 620-6162 to set that up.
FAQs

How long does a GAF bathroom waterproofing system last in Fremont? Installed correctly, 25 to 30 years, which is longer than the tile over it usually survives. The board itself is not what fails first – the assembly around it is. The drain flange and the preslope are where jobs die, and both come down to the installer. In Fremont’s climate you’ll get the full lifespan out of DensShield if it’s fastened and sealed to spec.
Can the waterproofing be repaired instead of replaced? Almost never. Once water has been wicking behind a board for months, the paper face is compromised and mold has moved into the framing. A patch of fresh board next to failed board doesn’t bond – you’ve just moved the failure point. Call (833) 620-6162 for an honest assessment; sometimes we’ll tell you the tile itself is fine and only the drain needs redoing.
How long does the swap take? A full gut bathroom in Fremont takes three to four weeks working a normal schedule – tear-out and framing first, then waterproofing and inspection, then tile, then fixtures and finish. A shower-only replacement runs about ten days. We don’t compress that timeline to win the bid; the preslope has to cure before the liner goes down.
How do you source the GAF parts? Through GAF’s published distribution channels, matched to the assembly in your home. We don’t carry parts on a truck and we don’t keep stock – every board and component comes in for your specific job, so the batch matches and the warranty documentation is clean. We’re an independent contractor, not affiliated with GAF. The full system gets installed to GAF’s published detail drawings, and the paperwork goes to you. We also carry KraftMaid, Cambria, and Silestone cabinetry and countertops if the vanity is in the plan.
If you’ve got a shower that’s been leaking into the floor joists or a bathroom in a 1950s Fremont ranch that’s due, call (833) 620-6162 and ask for Tom or one of his sons. Live person, 24 hours. Free estimate, no trip charge inside Alameda County, and a free second opinion on any written estimate you’ve already got. We’ll walk the bathroom with you, tell you what’s actually wrong, and hand you a written scope with the numbers on it.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












