







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Fence Installation: The Fremont Owner’s Guide
Aluminum ornamental fence installation in Fremont runs $4,000 – $10,000 for most residential runs, and that’s the honest number for a Jerith-grade system done with real footings and inspected permits. Jerith itself doesn’t install. They manufacture the panels, posts, pickets and gates; a licensed contractor sets them. We install Jerith and Jerith-compatible aluminum fencing across Fremont, and we’re an independent contractor, not affiliated with Jerith.

Owners usually call us after a windstorm or after they finally notice what the last dry season did. A post that was plumb in March has a lean by October. A gate that latched with two fingers now drags on the concrete. Or a panel is missing its bottom rail cap and the pickets have started walking in the channel. In Fremont, that pattern is so common it’s almost a calendar: our wet winters push clay soil around, then five dry months shrink it back, and a footing set too shallow shows up as a lean within a season or two.
Key Takeaways
- Jerith is a manufacturer, not an installer. You need a licensed contractor who knows the product line.
- Most “fence part” calls in Fremont turn out to be a footing or gate-sag problem, not a broken panel.
- Installed aluminum fence pricing here lands at $4,000 – $10,000 for a typical residential run.
- Permits matter. Fremont fences over a certain height and any fence in a front setback need review, and we pull them.
Which Jerith Models This Applies To

Jerith builds aluminum ornamental fence in several product lines, and the parts don’t swap between them. The two families most Fremont homeowners have are the traditional picket lines (think the classic spear-top and flat-top residential styles) and the heavier commercial-grade rail systems used around pools and along property lines shared with a busy street. Pickets, rails, brackets, post caps, and hinges are series-specific. A 3/4-inch picket bracket will not sit on a 5/8-inch rail, and a gate hinge drilled for the residential line won’t line up on the commercial hardware pattern.
Identifying what you have takes about five minutes. Measure the picket width with a tape, count pickets between posts, measure the rail height top and bottom, and look at the hinge style on any gate. Jerith stamps and labels appear on the brackets and inside post caps on many runs, and the manufacturer can confirm a series from photos. If you can’t find a label, the measurements alone usually settle it.
The OEM-versus-aftermarket call is real here. Jerith replacement parts are the safe match, especially for anything with a powder-coat finish, because an off-brand bracket will hit the color differently under Fremont’s hard summer sun within two seasons. Quality aftermarket aluminum brackets and hinges are fine for hidden hardware, and we’ll tell you plainly when aftermarket is a good buy and when it isn’t. We don’t stock parts and we don’t carry them on a truck. We order what your fence actually needs and bring it to the job.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Jerith Fence Installation Is Failing
These are the symptoms we see most, and what’s actually going on underneath each one.
- A post that leans after winter. Water got under the footing and the soil around it shifted. A leaning post is almost never the post’s fault; it’s the footing depth or drainage. Re-plumbing the post without fixing the cause means it leans again next spring.
- The gate drags or won’t latch. Gate sag on an aluminum run is usually hinge wear combined with a post that has moved a fraction of an inch. Replacing the hinge alone fixes it for a month. Setting the post and re-hanging the gate fixes it for years.
- Pickets walking out of the rail channel. The retaining screw or the rail cap has loosened, or the rail itself has flexed from a hit. Small fix, but catch it before a windstorm sends a picket into the neighbor’s yard.
- Powder coat chalking or flaking near the bottom rail. Sprinkler overspray and lawn chemical splash attack the finish first at the lowest point. Once the coating fails, bare aluminum starts to pit. It’s cosmetic until it isn’t.
- A panel that’s out of line with its neighbors. The run was set on grade that has since settled. On Fremont’s clay-heavy lots, an out-of-line panel is a grade problem, and patching the panel hides a footing that needs attention.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Aluminum fence installation in Fremont lands at $4,000 – $10,000 for most residential runs. The range is driven by linear footage, gate count, terrain, and how much of the existing fence can be reused. A run that’s mostly sound and needs new hardware, a re-set post, and a fresh gate re-hang sits at the bottom of that range. A full replacement with new footings, new panels, and a pair of gates sits at the top.

- Posts, panels, pickets, rails, brackets, caps and gate hardware: priced as a line item
- Footings dug to depth and set in concrete, not tamped into dirt
- Old fence removal and haul-off
- Permit pulled and inspection signed where the job requires it
- Labor and cleanup
Every scope and allowance is in writing before we start, and any change arrives as a written change order before work moves. Parts-plus-labor is broken out, not bundled into one number you can’t check. The work is backed by our 90-Day Done Right Promise: if something’s not right, Tom comes back and makes it right on one call. We also carry KraftMaid, Cambria, and Silestone on the kitchen and countertop side, because the same standard applies across every trade we touch.
DIY or Call Us?
You can safely check a lot of this yourself. Measure your picket and rail widths, look for loose brackets, tighten a hinge screw, and see whether a gate is dragging because of the hinge or the post. That’s a Saturday afternoon and a screwdriver.
Where it goes wrong is the post and the footing. Digging out a set post, re-setting it plumb at the right depth, and getting the run back on line without pulling the panels out of alignment is a job that punishes a first attempt. A post set into damp Fremont clay without proper depth and drainage will lean again inside a year. And a gate re-hang on a post that’s still moving is wasted work. If your fence is leaning, the gate is sagging, or a panel is out of line, call us at (833) 620-6162 and we’ll look at it and give you a straight answer. Estimates are free, and so is a second opinion on any written estimate you already have.
FAQs

With a properly set footing and intact powder coat, a Jerith aluminum run should hold up for 20 to 30 years or more. The finish is the first thing to go, and in Fremont’s dry, sunny summers, a fence getting full afternoon sun and sprinkler overspray will show coating wear earlier than one in shade. Call (833) 620-6162 for a free estimate if yours is showing its age.
Often, yes. A loose bracket, a worn hinge, or a single picket is a repair, and we’ll tell you so rather than sell you a whole run. A leaning post or an out-of-line panel is usually a footing repair. Call (833) 620-6162 and we’ll look at it before quoting anything.
A typical residential run takes one to three days, depending on footage, gate count, and how much old fence comes out. Jobs that need permits add review time before we start. Call (833) 620-6162 to schedule your free estimate and we’ll give you a real timeline for your fence, not a guess over the phone.
We order the parts matched to your specific series and measurements, and we don’t stock parts or carry them on a truck. That means the part that shows up is the part your fence needs, not whatever was closest. Call (833) 620-6162 for a free estimate, and take the 10% Senior & Veteran discount if it applies to you.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












