







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Roofing: The Fremont Owner’s Guide
Schluter makes a name for itself in tile and waterproofing, not in shingles. The “Schluter system” most Fremont roofs actually carry is KERDI, DITRA, or KERDI-BOARD used on tile details, flat roof transitions, parapet walls, and roof decks where tile meets waterproofing. If a Schluter membrane, drain, or edge profile on your roof has let go, you’ll usually find out the hard way: a brown ring spreading on a ceiling, a damp smell in the attic, or a tile edge that pops loose after a hard rain. Installed pricing for the membrane work that ties these systems in runs $400 to $1,800 for a localized repair and $8,000 to $20,000 when the failure is tied to a full tile roof replacement. We’re an independent contractor, not affiliated with Schluter, so when we tell you what a part costs we aren’t protecting a brand margin.

Roofing repairs around Fremont, CA get scheduled during our normal business hours. We answer the phone live, 24 hours a day, and we’ll get you a written scope before anyone climbs a ladder.
Which Schluter Models This Applies To

Schluter’s roofing-adjacent parts break into four families, and matching the right one matters because the specs don’t interchange. KERDI is the sheet membrane and goes on the flat or low-slope deck. KERDI-BOARD is the rigid foam backer with a waterproofed face, used on parapets and upstands. DITRA is the uncoupling membrane under tile, and DITRA-HEAT is the version with the heating cable grid. KERDI-LINE and the Schluter shower drains don’t belong on a roof at all, but homeowners routinely confuse them with roof drains, so check the label.
To identify what you have, pull a loose edge and read the printed membrane face: Schluter stamps the membrane type and width right on the sheet, most often 39-3/8 inches wide for KERDI rolls. If the printing is worn off, measure the thickness with calipers. KERDI runs about 8 mils, DITRA about 1/8 inch, and KERDI-BOARD 1/2 inch and up. Write those numbers down before you call anyone.
The OEM-versus-aftermarket call is different with Schluter than with, say, a GAF shingle. Schluter accessories (the KERDI-FIX adhesive, the KERDI-BAND sealing strip, the prefab corners) are cheap and unforgiving of substitutes. Generic band tape has a different fleece and won’t bond the same way in a wet Fremont winter. Use genuine Schluter there. The membrane itself and the drain hardware are where a quality equivalent is worth pricing, and we’ll show you both lines in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Roofing Is Failing
- A ceiling stain below a parapet or flat section. Water is getting past the KERDI lap or the KERDI-BAND seam. The membrane itself rarely fails; the lap does, which is the weak link on every membrane roof.
- Tile lifting at the edge of a roof deck. The DITRA or mortar layer under the tile has sheared. A missing or badly keyed edge profile lets water wick under and the tile loses its grip.
- Soft, hollow-sounding KERDI-BOARD on an upstand. The backer was installed with the wrong fastener or the face was punctured. Once the fleece is torn, the waterproofing is done.
- Bubbled paint or efflorescence on the fascia. Water is sitting behind the membrane and finding the drywall or wood below. In Fremont’s marine-layer climate, a slow leak can hide for two or three winters before it shows inside.
- A stained or damp area around a roof drain. The drain body wasn’t bedded in KERDI-FIX or the flange is loose. That’s a gasket-level failure, not a whole-roof job.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Repairing the Schluter detail on a Fremont roof lands in a few predictable bands. A localized membrane seam repair with genuine KERDI-BAND sits in the $400 to $1,800 range. Replacing a failed drain assembly or a run of KERDI-BOARD on a parapet fits the same band. If the leak has been running long enough to rot the deck under it, the repair turns into roof replacement, which runs $8,000 to $20,000 here. Tile roof work specifically runs $600 to $2,500 for the repair portion, and metal roofing, if that’s what you’re replacing, runs $15,000 to $40,000.
| Scope | Fremont Price Range |
|---|---|
| Membrane seam / detail repair | $400 – $1,800 |
| Drain assembly replacement | $400 – $1,800 |
| Tile roof repair (tile section) | $600 – $2,500 |
| Full roof replacement (if rot is found) | $8,000 – $20,000 |
| Metal roof installation | $15,000 – $40,000 |
What drives the spread: how much deck has to come up, whether the failure is one seam or the whole field, and whether the permit inspection requires a full re-cover. Every price change comes to you as a written change order before a nail moves, so the number on the invoice is the number on the estimate. Every eligible job gets permits pulled and inspections signed, and the work is backed by our written 90-Day Done Right Promise.
DIY or Call Us?
You can safely check a few things yourself. Pull a loose membrane edge and photograph the printed label. Measure the sheet thickness. Look at the attic from the access hatch with a flashlight for water stains. That’s the extent of it.
Here’s the part we want to be blunt about: this is a roof. It’s a fall hazard, and in Fremont the marine layer keeps a wet tile or membrane surface slick for most of the morning. Waterproofing laps have to run the right way (over, not under) and have to be sealed with the correct adhesive and a roller. Get it wrong and you’ll have a leak that didn’t exist before, in a spot you won’t find until the next rain. We don’t hand out step-by-step instructions for membrane seams on a pitched roof, and no honest roofer should. Call us at (833) 620-6162, and a live person picks up day or night.
FAQs

A properly bedded KERDI membrane will hold for 25 to 30 years of service, and a lot of the failure we see in the Bay Area comes from UV exposure before tile or the finish layer goes on, not from the material itself. In Fremont, where the sun burns hot in summer and the fog sits in fall, a membrane left exposed for a month or two weakens fast. Keep it covered and it lasts; leave it out and it won’t. Call (833) 620-6162 for a free estimate if you’re unsure of the age.
Usually yes. A single failed lap or a bad drain bedding is a repair, and it typically runs $400 to $1,800, not a full roof. The question is whether water sat long enough to rot the deck below, because that pushes the scope up. We’ll tell you which one you’re looking at in writing before work begins, and the second-opinion review on any written estimate is free.
A localized membrane or detail repair is usually a half-day to a full day on site, weather permitting. A drain swap is shorter. If the job turns into a full tile roof replacement, expect several days depending on roof size and whether the permit inspection is scheduled. We give you a written schedule up front, and the price doesn’t drift mid-job.
We specify the genuine membrane type and band from a local tile supplier and match it to the model you wrote down from the label, so the replacement spec is the same as what’s on your roof. We don’t carry parts on a vehicle or keep a warehouse of them; we source what the job calls for and put the line item on your written scope. KraftMaid, Cambria, and Silestone go into our interior work the same way: named brands, listed on paper, understandable to a homeowner who wants to look them up.
When you’re ready to price it, call (833) 620-6162 for a free estimate. A live person answers 24/7, we’ll bring a written scope, and if it’s an eligible repair over $200 you can take $40 off.
Written by the team at Barrett & Sons Construction Fremont, serving Fremont and nearby areas.












